Technical regulations Formula Offroad

MODIFIED CLASS

APPROVED VEHICLES
All vehicles must have two axles and four wheel drive.
All vehicles must have a bodyshape that resembles a mass produced vehicle.
All vehicles licensed after 01012006 must have two seats installed side by side.

1. Chassis
1.1 Frame and chassis structure.
The main frame structure must be constructed of: (applies only to vehicles licensed after 01.01.2006)
• Original frame from a mass produced 4×4 vehicle,
or
• Seamless steel tubing of minimum size 45×2,5mm or 50x2mm (350 N/mm2), or
• Square tubing of minimum size 40x60x3mm (350 N/mm2)

Aluminum or Chromemoly steel is not allowed.

2. Wheels and suspension
2.1 Tires
Paddle tires type “Multipaddle” or “Padla Trak” are allowed.
All types of tires approved for street use is allowed. It is not allowed to custom groove resurfaced tires.
Snow chains or any kind of attachments to improve traction is not allowed.

2.2 Wheels
Free of choice.

2.3 Suspension
Free of choice.
Active, adjustable suspension is not allowed in competition.
For vehicles licensed after 01.01.06 properly mounted bumpstops of gas charged hydraulic design is mandatory.
This is also highly recommended for older vehicles.

2.4 Shock absorbers
Free of choice

3. Drivetrain
3.1 Engine
Free of choice.
Supercharger(s) or Turbocharger(s) are allowed.
For roots type superchargers a shield made of 1,5mm steel or 2,5mm aluminium must cover the drive belt. The shield must be securely mounted to the engine or chassis. Any fuel, nitrous or oil hoses nearby the drive belt must be enclosed in steel pipe or be of a steel reinforced type. SFI approved limiting straps must me installed in case of a supercharger blowing off the manifold. All fuel hoses must be long enough as to not break in such a case.
Harmonic balancer (if so equipped) and flexplate/flywheel must be of racing type.
Dual, correctly working return springs must be installed on the carburettor/throttle body.

3.2 Fuel system
Fuel tank must be designed for racing and securely fastened. It must not be installed in the driver compartment. There must be a wall to prevent fuel leaking into the driver compartment in case of a rollover. The fuel cap must be leak proof and a check valve must be installed in the vent hose.
All fuel lines must be one-piece and securely fastened. Any fuel lines passing through the driver compartment must pass through a steel tube of 1mm thickness with a diameter of 2 times the diameter for the fuel line.
Diesel, Gasoline and Racing gasoline is allowed.
Lead substitute and Octane booster is allowed. All other fuel additives are banned.
Nitrous oxide is allowed if installed according to appendix A.

3.3 Cooling system
Radiator and overflow tank is not allowed the driver compartment. All hoses must be undamaged and of high quality.
Any hoses or tubes passing through the driver compartment must be covered and without splices.

3.4 Exhaust system
Free of choice. Noise level can not exceed 110dB according to FIA measurement rules.

3.5 Electrical system
Battery must be of dry cell design and securely mounted with upper and lower brackets. The positive battery post must be securely covered with a non conductive material.
All cables must be securely fastened.
An electrical master switch must be installed in reach of the driver when sitting with the seatbelts tightened. A second switch or a wire actuating the primary switch must be installed in the rear of the vehicle. The rear switch or release handle must be clearly marked with a blue triangle and a red lightening inside the triangle.

3.6 Transmission and drive shafts
Free of choice. Automatic transmissions must have a properly working neutral safety switch and a flexplate/transmission shield made from 6mm thick steel plate or SFI approved.
Transmissions with a SFI approved bellhousing do not need these shields.
Vehicles with manual transmissions must have the starting current wired through a brake light switch.
Front and rear driveshafts must have a safety loop made of 5x50mm steel bolted to the chassis or transfer case with minimum two grade 8.8 M10 bolts. The safety loops must be on the transfer case end of the drive shafts.

4. Brake system
4.1 Regular brakes
Free of choice, but must be operated by foot, positively work on all four wheels and capable of locking up all four wheels simultaneously.
Driveshaft mounted brakes are not allowed.

4.2 Parking brake
Properly working handbrake and/or park function in transmission must be installed.

4.3 Brake lines
All brake lines must be undamaged and securely fastened.

4.4 Steering brake
No form of steering brake system is allowed.

5. Steering system
5.1 Steering parts
The vehicle must be controlled by a conventional steering wheel mounted in front of the driver. All steering components must be well dimensioned for safe control of the vehicle at all times. All hydraulic hoses must have pressed-on ends, be free of any damages and have sufficient length to allow full movement of the suspension.
All steering hoses must be protected from potential damage caused by engine or suspension components.
Four wheel or mid-chassis steering is not allowed.

6. Body
6.1 Bodyparts
The bodyshape must resemble a mass produced vehicle. The length of the body must cover the wheelbase of the vehicle. Hood, side body panels, front and rear fenders must be installed and resemble the original vehicle.
Engine air intake protruding through the body must be designed to protect the driver from direct blowback from the carburettor/throttle body.
Any windows must be made of laminated glass or polycarbonate/lexan.

6.2 Driver compartment
Walls separating the driver’s compartment from the engine, oil coolers and radiator must be installed. The purpose is to prohibit fluids and/or flames spreading.
If the engine air intake is in the driver’s compartment it must be baffled to protect the driver from any blowbacks.
If the driver does not use armstraps a window net with maximum 50mm web size and minimum 2mm thread size must be securely installed.
The distance from the top of the driver’s helmet to the top of the rollcage must be at least 10cm.

6.3 Floor
Floor of the vehicle must be made of 1mm steel or 2mm aluminium and completely cover the whole floor. If the front driveshaft passes under the driver seat, the material in this area must be at least 2mm steel or 3mm aluminium.

6.4 Drivers seat
Seat must be of racing type and have holes for a 5 point seat belt.
Seat must be securely fastened and the back of the seat must rest against the rollcage or braced in a similar way. If the seat is mounted on a sliding bracket, there must be an extra safety pin installed to prevent sliding of the seat.

6.5 Rollcage
6-point rollcage according to appendix B mounted directly to the frame must be installed.

6.6 Seatbelts
Only 3” wide FIA/SFI approved seat belt with 5 or more fasteners is approved.
Seat belt must be undamaged and must be within approved date markings.
Shoulder straps must be installed in line with the drivers shoulder or lower such that the angle between the back of the seat and shoulder straps is between 45 and 90 degrees. If the seat belt is installed using bolts the bolts must be minimum M10 bolts with of at least 8.8 grade. If the bolts are installed in the bodywork, the area must be reinforced with a 2mm steel plate of at least 20cm2.
Drilling in the rollcage for mounting seatbelts is not allowed.

7. Miscellaneous
7.1 Lights
Any external lighting made of glass must be taped over during competition.

7.2 Gauges and switches
Free of choice

7.3 Towing hooks
Front and rear towing hooks or eyes with at least 35mm diameter hole must be in the front and rear of the vehicle.
There must also be similar eyes or hooks on the top of the vehicle for lifting – preferably in the balance point of the car.
Towing and lifting points must be marked in bright color to stand out.

7.4 Communication
Communication between driver and a person outside the vehicle is not allowed while the vehicle is in a track.

7.5 Weight
Minimum weight without driver is 600kg. Any extra weight must be securely fastened.

7.6 Extra equipment
Any extra equipment (flags, aerodynamic wings, etc.) must be securely fastened and must not pose as a potential hazard to the driver or spectators/officials.